This illustrated guide written by Glenn Watt walks you through how to install the C. B. Gitty Part number 54-020-01, “Pre-Wired 4-String Single Coil Pickup Harness with Volume and Tone.” Cutout and drill bit sizes are given and the steps clearly shown for mounting one of these handy pre-wired pickup harnesses into cigar box guitars.
The principles in this guide can also be used for most any single-coil or humbucker pickup with a neck-through cigar box guitar, where you often have to notch down into the neck (and brace underneath it) to get the pickup into place.
So you want to hear that new gitty you’re building through your amplifier that’s been sitting unused behind the holiday decorations in the basement? Do you want to make certain that you can crank that little bad rabbit when everyone leaves and you’re left to your own devices in a quiet home? Or maybe you’re looking to level-up and retro-fit a pickup into a guitar you already have that’s been sorely needing a little volume. In the Pre-Wired Piezo and Jack Harness from C.B. Gitty you have the simplest way to electrify your instrument with the most basic of installation requirements.
Here is an easy project for you to try – making a tambourine from a cigar box!
Ben “Gitty” Baker walks you through the steps he followed to build one, along with photos of some of the steps. These are “loose” plans (more of a builder’s diary, really) with lots of room for interpretation. There is no “right way” – Ben had never built a cigar box tambourine before, and made it up as he went along, and you should too! So let’s get started…
Fretting directly onto a guitar neck is a great option to showcase the natural beauty of the wood you have chosen for your neck, rather than using a fretboard. However, this does make using a traditional nut a bit more challenging. This article shows you one way you can install a bone (or hardwood) nut blank onto your fretted cigar box guitar neck.
Fretting directly onto a guitar neck is a great option to showcase the natural beauty of the wood you have chosen for your neck, rather than using a fretboard. However, this does make using a traditional nut a bit more challenging. Continue reading “How to Notch a Fretted Cigar Box Guitar Neck for a Nut”
One of the most frequent questions we hear from new cigar box guitar builders is what strings they should use on their cigar box guitar, and how they should tune it. This can be very mysterious for a builder, especially folks without a background in music. While it is often said that there are no rules when it comes to building CBGS (and that is often true, which is one of the great things about this hobby), it can be frustrating to hear when you just want a simple answer to a question. In this article, we’ll try to demystify some of the theory behind strings and tunings, and also give some straightforward, clear answers for those who just want to know what to do.
First, we’ll give a clear answer for those of you who just want to know what to do: at C. B. Gitty Crafter Supply we consider a “standard” cigar box guitar to be a 3-stringer with medium-gauge acoustic strings tuned to either Open G (for slide playing), or G-B-E for fretted playing. The strings used are equivalent to the three highest-pitched strings on a standard six-string guitar, and the scale length of the instrument (the distance from the nut to the bridge) is around 25 inches.
This happens to be the most popular set of CBG strings we sell in our shop – our C. B. Gitty 3-String Acoustic Medium Open G/Standard Set. If you are building your first cigar box guitar and have no idea what to do or what you need, start with these strings. These strings are based on a “medium” weight set sold for a standard 6-string but include only the 3 highest-pitch strings (the smallest/lightest ones) from the pack, so you don’t have any leftovers. It can be tuned either in “Open G” for slide playing (G-B-D) or if you have a fretted neck it can be tuned like the 3 highest-pitch strings of a standard guitar (G-B-E).
If you have been unsure of how to make use of the cigar box guitar chord forms we’ve been adding to the knowledgebase here on CigarBoxGuitar.com, this document is for you! In this 3-page illustrated PDF we walk you through how to interpret the chord forms so that you can put them to use in your playing. Continue reading “How to Read and Use Chord Forms for Cigar Box Guitars”
In this video, Ben “C. B. Gitty” Baker and Glenn Watt show you the basics of getting your cigar box guitar in tune. Both tuning “by ear” and using a digital tuner is covered, so even if you have no experience with musical instruments or tuning, this video will help you get started. At the end of the video, Ben and Glenn even do a little bit of jamming with their newly-tuned cigar box guitars. Continue reading “How to Tune a 3-string Cigar Box Guitar to Open G GDG”
Hard-tail bridges are a must-have piece of hardware for building professional-level electric guitars and cigar box guitars. This article walks you through the different styles and varieties, as well as how to install them on your special build.
What are Hard-tail Bridges?
This cigar box guitar sports a gold-plated 3-string hard-tail bridge. It is a “Metamorphosis” model built by Glenn Watt at C. B. Gitty.
Hard-tail bridges are pieces of hardware often seen on solid body electric guitars. They combine bridges and saddles in such a way that the intonation and string action (height over the fretboard) can easily be adjusted post-install. These styles of bridges are best known from Fender’s Stratocaster™ electric guitars.
Because of how they are made, hard-tail bridges work best when used with magnetic pickups (the sort seen on solidbody electric guitars) as opposed to piezo-style pickups. They help with achieving a professional intonation, maintaining a nice low string action, and increasing sustain (due to their solid metal construction).
This 6-string hard-tail bridge has an opening for a single-coil pickup. This item is available ready-to-install from CBGitty.com.
Some hard-tail bridges also include openings for pickups such as Fender-style single coils and humbuckers. The basic versions just have the bridge and saddle components.
Although they are best known for use on solid body electrics, hard-tail bridges also work great for cigar box guitars. There are now 3 and 4-string varieties available, which make them even more suitable for electric cigar box guitars that have magnetic pickups.
Learn about the “sealed-gear” varieties of guitar tuners/machine heads, and some useful tips, tricks and advice on how to use them properly.
What are Sealed-Gear Tuners?
Sealed-gear tuners (also known as machine heads, tuning pegs and other names) are the type often seen on electric guitars, especially Fender Telecaster™ and Stratocaster™-style guitars.
They are designed so that the mechanical gears of the tuner are sealed into the base, as opposed to open-gear tuners where the worm and pinion gears are visible.
A strap button is a piece of hardware mounted to a guitar or other instrument, as an anchor point for attaching a strap.
A strap allows the instrument to hang from the musician’s shoulders, making it more comfortable to hold and play, especially when standing up.
A strap allows an instrument to hang comfortably from musician’s shoulders while standing.
While strap buttons are optional on a guitar, including them will make the instrument much more appealing to a person used to performing on stage, and can lend more of a professional, finished look and feel. We recommend that builders always put them on their cigar box guitars. Continue reading “How to Use Strap Buttons”
